Brix 38x14 - boats - by dealer - marine sale - craigslist (2024)

Brix Marine Hammer Cat Available!

Twin Mercury V12 600 HP

BRIX MARINE HULL
Length 38' : Beam 14'

Longitudinal t-bars
Longitudinal hull stiffeners
Floor framed on 26" centers
Self bailing aluminum decks
3814-CTC Offshore SWA

BEACHCOMBER landing gear
Foot traffic only
Aluminum drop bow door
SS door retainer clip
WARN DC800 industrial hoist, black 12V
Hull beaching plates

Deck Accessories
Extended T-transom c/w hinged aluminum gate
Hand rails fore & aft deck
Roof access ladder c/w flat rungs
(2) Side boarding doors (port & stbd)
Folding SS gunnel step (port side)
Gunnel trays aft deck (port & stbd)
(1) Hull access hatch c/w gas strut & flush hinges & ladder
(1) Generator access hatch c/w gas strut, flush hinges & ladder
(2) Fish storage lockers insulated c/w gas struts, flush hinges & macerator for discharge
(2) Battery lockers c/w hinged doors, vents & drainage ports
Compression latch, 316 SS, locking
(2) Fish cleaning stations c/w two drawers (black) & overboard gut chute (1 port & 1 stbd)
Approx. 52" x 30"
Top cambered toward overboard gut chute
360 degree fiddle w/ stepped down fiddle height at working edge
Removable starboard cutting surface (black)
Hidden magnetic knife keep on aft, inboard corner
(5) Welded aluminum rod holders on aft edge
Second station c/w hinged door & latch
(2) Watertight 12" round liftout hatches in outboard well
(8) 11" tie up cleats
(1) 8" tie up cleat
Anodes for cathodic protection
Swim ladder - deploys from under T-transom & includes vertical hand rails
Alaskan overhang roof extension
(9) Aluminum rod holders (locations TBD)
(4) Aluminum coat hooks under exterior overhang
Sink c/w mixer faucet on the aft deck (port side)
(2) Downrigger pads (locations per drawing wired for Scotty)
Removable aluminum tow post c/w stowage bracket in the outboard well
Install OFE 80 gallon X-tream bait tank includes; Through deck soft patches for water &
electrical connections. Bolt on "Tank Stays" from manufacturer c/w helicoil deck fittings.
Separate raw water supply pump w/ thru hull & strainer. Overflow raw water to side
thru hull c/w ball valve. DC control panel for pumps & tank lights located at aft station.
UMT ECO 600 roof mounted dingy davit c/w roof mounted
AB Inflatable c/w Yamaha 15hp motor, tiller, prop - includes fuel tank, lifting sling, chock pads
Lammina 10AL inflatable dinghy
Yamaha 15hp outboard w/ prop
Fuel tank - 6 gallon bow tank
Universal Dinghy chocks
SS ratchet straps x 10'
Sling
Crab pot puller w/ 12v plug
Electra-Dyne 12V pot puller (250lb max load)
ED7500-10 XHD w/ SS disc (20:1) 290 FPM max
SS Davit (removable) c/w gunnel grommet
Open block, fairlead roller, rope deflector & hand control included

CUSTOM EXTERIOR COVERS
Custom aft station cover Stamoid Black c/w SS fasteners & PTFE thread.
Custom Fly bridge helm station cover Stamoid Black c/w SS fasteners & PTFE thread.
Custom Fly bridge helm chair cover, Stamoid Black c/w SS fasteners & PTFE thread
Custom Fly bridge bench covers 1-port, 1-stbd, Stamoid Black c/w SS fasteners & PTFE thread.

STARBOARD-WALK-AROUND CABIN
BRIX Headliner: fully insulated with easy to clean white fiberglass
& Black wood trim w/ black screws
Overhead grab rails along centerline
BRIX Walls: fully insulated with Black carbon fiber finish & Black wood trim w/ black screws

Hull Length 38'
Waterline Length 36'
LOA ~47'
Beam 14'
Lightship Weight ~20,000 lb
Max HP 2 x 600HP outboards
Fuel Capacity 2 x 250 gal
Note : figures vary depending on final outfitting & conditions
BASE SPECIFICATION
BRIX MARINE HULL
Length 38' : Beam 14'
5086 alloy aluminum hull skins
5052 alloy aluminum interior transverse frames
Longitudinal t-bars
Longitudinal hull stiffeners
Floor framed on 26" centers
Self bailing aluminum decks
3814-CTC Offshore SWA
Upgrade model from 3814-CTC SWA to 3814-CTC Offshore SWA
Offshore model extends both the aft deck & LOA by approx. 32"
with addition of offshore brackets for outboards.
T transom does not support a fish locker in the offshore model
Tandem offshore brackets designed for 35" outboard shaft length
Modify offshore brackets to extend to outside plate & angled to gunnel height
BEACHCOMBER landing gear
Foot traffic only
Aluminum drop bow door
SS door retainer clip
WARN DC800 industrial hoist, black 12V
Hull beaching plates
Deck Accessories
Extended T-transom c/w hinged aluminum gate
Hand rails fore & aft deck
Roof access ladder c/w flat rungs
1 of 9
(2) Side boarding doors (port & stbd)
Folding SS gunnel step (port side)
Gunnel trays aft deck (port & stbd)
(1) Hull access hatch c/w gas strut & flush hinges & ladder
(1) Generator access hatch c/w gas strut, flush hinges & ladder
(2) Fish storage lockers insulated c/w gas struts, flush hinges & macerator for discharge
(2) Battery lockers c/w hinged doors, vents & drainage ports
Compression latch, 316 SS, locking
(2) Fish cleaning stations c/w two drawers (black) & overboard gut chute (1 port & 1 stbd)
Approx. 52" x 30"
Top cambered toward overboard gut chute
360 degree fiddle w/ stepped down fiddle height at working edge
Removable starboard cutting surface (black)
Hidden magnetic knife keep on aft, inboard corner
(5) Welded aluminum rod holders on aft edge
Second station c/w hinged door & latch
(2) Watertight 12" round liftout hatches in outboard well
(8) 11" tie up cleats
(1) 8" tie up cleat
Anodes for cathodic protection
Swim ladder - deploys from under T-transom & includes vertical hand rails
Alaskan overhang roof extension
(9) Aluminum rod holders (locations TBD)
(4) Aluminum coat hooks under exterior overhang
Sink c/w mixer faucet on the aft deck (port side)
(2) Downrigger pads (locations per drawing wired for Scotty)
Removable aluminum tow post c/w stowage bracket in the outboard well
Install OFE 80 gallon X-tream bait tank includes; Through deck soft patches for water &
electrical connections. Bolt on "Tank Stays" from manufacturer c/w helicoil deck fittings.
Separate raw water supply pump w/ thru hull & strainer. Overflow raw water to side
thru hull c/w ball valve. DC control panel for pumps & tank lights located at aft station.
UMT ECO 600 roof mounted dingy davit c/w roof mounted
AB Inflatable c/w Yamaha 15hp motor, tiller, prop - includes fuel tank, lifting sling, chock pads
Lammina 10AL inflatable dinghy
Yamaha 15hp outboard w/ prop
Fuel tank - 6 gallon bow tank
Universal Dinghy chocks
SS ratchet straps x 10'
Sling
Crab pot puller w/ 12v plug
Electra-Dyne 12V pot puller (250lb max load)
2 of 9
ED7500-10 XHD w/ SS disc (20:1) 290 FPM max
SS Davit (removable) c/w gunnel grommet
Open block, fairlead roller, rope deflector & hand control included
CUSTOM EXTERIOR COVERS
Custom aft station cover Stamoid Black c/w SS fasteners & PTFE thread.
Custom Fly bridge helm station cover Stamoid Black c/w SS fasteners & PTFE thread.
Custom Fly bridge helm chair cover, Stamoid Black c/w SS fasteners & PTFE thread
Custom Fly bridge bench covers 1-port, 1-stbd, Stamoid Black c/w SS fasteners & PTFE thread.
STARBOARD-WALK-AROUND CABIN
BRIX Headliner: fully insulated with easy to clean white fiberglass
& Black wood trim w/ black screws
Overhead grab rails along centerline
BRIX Walls: fully insulated with Black carbon fiber finish & Black wood trim w/ black screws
BRIX Deck: slip-resistant vinyl and light weight acoustic dampening insulated subfloor
Loncoin II vinyl raised disc flooring (Sonic Gray)
Welded aluminum dash console c/w painted removable lower cover panel
Fixed forward facing bench seat (port side)
Lift out seat base c/w ballistic nylon black cushions for storage access
(2) Folding footrests (black)
Grab rail over dash panel
Centerline deck storage in main cabin c/w hidden hinges
Quarter berth in port hull
Hinged companionway access c/w sliding top
Walls wrapped in light gray hull liner
Sleeping cushion w/ ballistic nylon black cushion
Heater outlet
Wrap-around settee lounge
Adjustable table base converts to berth
Table top - 3/4" white quartz (Arctic White)
Liftout seat bases & storage c/w ballistic nylon black cushions
(2) Sliding drawers in aft seat base
(2) Sliding drawers in fwd seat base
Helm seating
Llebroc Mako 42" double bench seat - Ebony w/ Plum insert color black powder coat arms
Triple slide adjustment
Painted aluminum seat base w/ footrest & open storage
3 of 9
Galley
Corner joinery
Laminate finish - Drift wood vertical grain w/ black edges
Large capacity built-in fridge/freezer (8.1/2.1 Cu. Ft.)
Locate a standard 120V AC outlet over refrigerator for - microwave NIC
Galley counter joinery
3/4" white quartz (Arctic White) counter top c/w matching backsplash
Black Starboard & SS button latches
Electric cooktop
(4) Sliding drawers under cooktop
Centerline drawer c/w double door storage under & adjustable shelf
SS sink & mixer faucet (includes wooden counter leaf & tip-out tray)
Storage door under sink
Island joinery
Double door storage c/w adjustable shelves
Open map storage on fwd face
Cuddy
BRIX Headliner: fully insulated with easy to clean white fiberglass
& black wood trim w/ black screws
Drop floor entry
(2) 3" Cushions covered w/ Ballistic nylon Black
(2) Lewmar 60 low profile hatch
Lewmar hatch screen & blackout blinds
(2) Privacy curtains at entrance
Liftout hull access hatches port & stbd (under cushions) c/w bilge access ladders
(4) Storage shelves in fwd bulkhead (2 port & 2 stbd)
Laminate face frames, hinged doors Black Starboard & SS button latches
Storage split stateroom berths for Cuddy Cabin
Joinery divider w/ laminate finish & SS button latches
(1) Storage door in cuddy entrance
(2) Storage doors in joinery in each stateroom (4 total)
Head
BRIX Headliner: fully insulated with easy to clean white fiberglass & Black wood trim w/ black screws
3/4" white quartz (Arctic White) counter top
Electric marine toilet c/w fresh water flush
SS shower kit w/ hot & cold water control & overboard floor drain
Solar powered exhaust fan
Toilet paper holder
Teak framed mirror (wall mounted)
4 of 9
SS sink & combination faucet
Open Flybridge
Welded aluminum dash console c/w hinged access door
Flybridge detachable radar & antenna super mast
Aluminum venturi
Access ladder/incline stairs (replaces roof access ladder)
Flybridge helm seat - Black shell Charcoal/Gray cushion
Fabricated aluminum seat box c/w 3 side pipe footrest
(2) Navigator flybridge bench seats c/w storage & ballistic nylon black cushions
3" cushions ballistic nylon black c/w drainage cloth
Removable cover for flybridge helm station & second station console on the aft deck
(2) Aluminum storage cabinets under brow areas port & stbd c/w outboard hinged door
& locking SS T-handles
Removable double kayak rack
Water System
55 gal fresh water tank w/ deck fill, vent & gauge
35 gal black water tank w/ "Y" valve, macerator, deck pump out & gauge
6 gallon SS water heater (requires 110VAC power source | genset or shore power)
Raw water wash down system c/w SS spigot (location)
Fresh water wash down system c/w SS spigot (location)
Pressurized water system
Sea Water Pro, water maker c/w (20 gal. per HR)
1" raw water system c/w strainer
Polar Cap Ice maker c/w Ice management system piped to insulated fish holds
Automatic Outboard engine Flushing System - 2 engine setup
OFS quick disconnect deck kit-straight
OFS V1.5-2.0 remote switch w/ 12' harness & cover panel
Bilge system
(4) 2000GPH bilge pumps w/ float switches & high-water alarm
Windows
(3) Clear bonded windshields
(3) Tinted, sliding, black miter-frame side windows
(3) Tinted, fixed, black miter-frame side windows
(1) Frosted, sliding, black miter-frame window
Screens on all opening windows
5 of 9
Doors
Sliding aft door w/ clear window & lock
Upgrade aft cabin door to full height window
Sliding side door w/ tinted window & lock
BRIX hinged door w/ lock & (3) coat hooks
HVAC
Main cabin hydronic defrost & heat system (includes head)
Dial-a-Watt heater (requires 110VAC power source | genset or shore power)
Webasto Platinum 22K BTU marine air conditioning system c/w ducted distribution
DC Electrical
AGM battery pack - (2) group 31 starting batteries for engines
AGM battery pack - (4) 6V deep cycle batteries for house loads
AGM battery - (1) group 24 starting battery for generator
Remote battery switches w/ dash mounted controls & automatic charging relays (ACR)
(1) 12V power outlet
(1) 12V dual USB port
(2) Multiple speed air circulation fans
Surface mount 187 Series circuit breakers
LED navigation lights
Pantographic windshield wipers w/ washing system
DC distribution panel
Bilge pump panel switch
(2) 12V Dual USB charging ports to cuddy cabin
Install Black Oak camera on port end of mast wing connect to Garmin display
Install (2) Black Oak infrared pucks under mast wing (port & stbd)
Install puck lights on single switch dash mounted under remote battery switches
as possible
AC Electrical
30A AC Shore Power System
Smartplug shore power inlet c/w 50' cordset
30A Galvanic isolator
(4) 15A Duplex receptacles on GFCI circuit
AC distribution panel
Blue Sea ELCI c/w enclosure
Inverter/charger (c/w battery)
Victron MultiPlus 12V/3000VA Inverter/charger, 120A
Victron Digital Multi Control GX
6 of 9
Generator
Northern Lights diesel generator (12kW)
Remote operator panel w/tachometer
Raw water cooling
Wet exhaust (includes Gensep)
Lights
(4) LED red/white cabin lights (main cabin)
(1) LED red/white cabin light (quarter berth)
(2) LED red/white cabin lights (galley)
(2) LED red/white cabin lights (cuddy)
(1) LED red/white cabin light (head)
(8) LED gunwale courtesy lights
(2) Rigid D-Series PRO LED deck lights - aft (main & flybridge switching)
(1) Rigid D-Series PRO LED deck lights - fwd (main & flybridge switching)
(1) Rigid D-Series PRO LED deck lights - port (main & flybridge switching)
(1) Rigid D-Series PRO LED deck lights - stbd (main & flybridge switching)
LED Searchlight c/w remote control - 12V/24V (main switching)
Install OFE Sunbright Series 20 lightbar on mast just below searchlight.
Cut fab and weld custom bracket shelf w/ supports for lightbar.
Install factory switch at main helm dash.
Upgrade DC circuit breaker & wiring as required by ABYC
Electronics & Navigation
Premium electric trumpet horn (main, aft & flybridge switching)
Magnetic compass, bulkhead mount (main stn)
Fusion stereo c/w CD/DVD, Bluetooth, AM-FM,3-zone, MP3 & 4
(4) Fusion shallow mount speakers, white
AM/FM antenna & SS base
Garmin GPSMAP 8616xsv MFD/Sonar, US+Can (main station)
Garmin GPSMAP 8616 MFD (main station)
Garmin Twin SD card reader for 8000 series - USB
Garmin VHF 215 radio w/ hailer, antenna & removable mic (main station)
Garmin GPSMAP 8616 MFD (second station)
Bail mount w/ knobs for 16" chartplotter
Garmin GPSMAP 8616 MFD (flybridge station)
Garmin GHS 11 remote wired handset (flybridge station)
Garmin GPS antenna
1kW SS CHIRP transducer
GMR 18HD+ 4kW radar w/18" HD dome, 36 NM range
NMEA 2000 networking system
7 of 9
(2) Garmin GC 200 marine IP cameras, 1 fwd on super mast, 1 aft under Alaska roof overhang
Power
Mercury 2 x 600HP V12 Verado Black outboards
Main Station DTS controls
Joystick
Contra-rotating propellers
Power trim
Power tilt
Mercury 3 year limited warranty
Mercury 600HP V12 Second Station c/w DTS controls & joystick
Mercury 600HP V12 Third Station c/w DTS controls & joystick
Fuel System
Twin 250 gal. aluminum fuel tanks c/w analog gauges
EPA compliant fuel tanks, vents & fills
Transom mounted fuel filters (one per engine)
Mercury primary fuel filters (included)
20 gal. diesel tank c/w fill & vents
Racor 120 series diesel fuel filter
Safety Package
Type B-1 fire extinguisher ABC (5lb)
Marine carbon monoxide detector (MTI 65-541)
Gasoline fume detector
Smoke detector
Anchoring & Mooring
Lone Star electric drum winch c/w rode, chain, bow sprit & MMX-5 anchor
Battery added to house bank
Elite 4 winch c/w brushless variable speed 12V motor
DB nylon rode 1/2" x 300' & 30' x 5/16" chain
CR195 deck roller & large anchor swivel
CX600 bow sprit +2 (nylon front and 3 trailing roller)
MMX-5 Hi holding power anchor
8 of 9
Paints & Finishes
Clear coat protective finish
Interior painted with low-glare marine paint
Main cabin - Hamlet Black
Head - Marble Stone
Durable non-skid deck coating black
Vinyl hull decals (black, white)
Hammer Cat
Kalama, WA
Black vinyl window accents
Vinyl wrap selections
Vinyl wrap cabin - deck to roof c/w accent stripe along port & stbd roof edge
Vinyl wrap hull - Keel to transom & waterline to shear pipe
AF bottom paint c/w epoxy barrier & 3 coats of bottom paint (black)
Wrap Supermast w/ stock 3M wrap - Matte Dark Gray
Wrap splashwell transoms & splashwell inside triangles w/ stock 3M wrap - Matte Dark Gray
Fairing
Full fairing includes 14 lay days @ Westport
(2) Lay days @ Westport to wrap hull includes offsite travel lift fees & additional round trip
Commissioning & Delivery
Notarized Bill of Sale
Manufacturers Certificate of Origin
COTS manual binder - "Commercial Off The Shelf" manuals
Care & Maintenance binder
One day of combo dock & sea trials w/ Brix technician(s) on board
Three days of dockage in Port Angeles Marina
Complete USCG Vessel Documentation
• obtain Certificate of Documentation with recreational endorsem*nt.
Extended (5-year) expiration included.
• CNC cut Official Number plate and weld in visible, interior section of hull.
Note: NVDC turnaround time varies.

................................Please call Craig at 503-705-9110.............................